Most GE washer repairs in Sherman involve the same few systems: the drain pump, the lid or door lock, the drive, the water supply and the controls. Below are independent repair companies serving Sherman, with those that mention GE first, then the nearest appliance repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Washer Technicians, Sherman TX
We found 22 appliance repair companies within 30 miles of Sherman. 3 of them are based in Sherman itself, and the rest are spread across McKinney (9), Durant (3), and Anna (2). None of the repair companies near Sherman name GE in their listings, so we show the closest appliance repair companies. Ask each one about your machine before booking. The closest is Mckinney Services, about 1.1 miles away. Across 20 rated companies, the average public rating is 4.3 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Companies within 30 miles | 22 |
|---|---|
| Mention GE | 0 |
| Open on Saturdays (per listing) | 18 |
| Name washers or washing machines in their listing | 4 |
| Three nearest companies, miles away | 1.1, 4.6, 5.7 |
| Rated 4.5 stars or higher (10+ reviews) | 11 |
The leading options for Sherman are Sears Appliance Repair (4.6 miles away, 4.5 stars from 296 reviews, lists Saturday hours); Sears Appliance Repair (28.7 miles away, based in Durant, 4.8 stars from 83 reviews, lists Saturday hours); Pilot Point Appliance Repair (25.2 miles away, based in Pilot Point, 4.2 stars from 30 reviews, lists Saturday hours); Zoom Appliance Repair LLC (21.6 miles away, based in Anna, 4.8 stars from 247 reviews, lists Saturday hours).
GE Washer Lines Technicians Work On
What Makes GE Washer Repairs Different
The drain hose should use the included anti-siphon clip and must not be pushed too deep into the standpipe or taped in place, which can siphon water out of the washer. Source: GE Appliances - Front Load Washer - Troubleshooting
On electronic top load models the lid locks automatically during parts of the cycle and stays locked until the basket has coasted to a full stop. Source: GE Appliances - Top Load Washer - Display and Status / Feature Lights
Common GE Washer Problems
- Washer not draining. Wait out normal pauses between cycle steps, then look for a kinked or clogged drain hose, a drain set too high, or a clog shown by a Po code or flashing Rinse light. Source: GE Appliances - Top Load Washer - Will Not Drain
- Washer off balance or shaking. Remove some items from an overfilled basket or spread bunched items evenly, then make sure the washer is level. Source: GE Appliances - Frequently Asked Questions About GE Washers
What GE Washer Codes Mean
| Code | What it means |
|---|---|
| Po (or flashing Rinse light) | The washer is draining slowly, usually from a clog or a pinched drain hose. Source: GE Appliances - Top Load Washer - Will Not Drain |
| dE / E2 | The lid was opened during the cycle; close it and press Start to resume. Source: GE Appliances - Washer - Consumer Help Indicator |
| CAnCELEd | The cycle was paused for more than a day or was stopped by certain errors. Source: GE Appliances - Washer - Consumer Help Indicator |
Signs Your GE Washer Needs a Technician
- Washer will not spin, or clothes come out soaking wet
- Washer will not start or the lid or door stays locked
- An error code on the display
What Gets Fixed on a Sherman Washer Call
Care GE Recommends for Its Washers
- Leave a top load lid up when the washer is not in use so the inside can dry out. Source: GE Appliances - Frequently Asked Questions About GE Washers
- To clean a top load tub, fill it with hot water at the highest level, add a cup of chlorine bleach, and run a regular wash cycle. Source: GE Appliances - Frequently Asked Questions About GE Washers
Brand guides: GE Washer Not Draining or Spinning: What to Check.
What GE Washer Repairs Cost
Most GE washer repairs involve common parts and an hour or two of labor. For reference, published cost guides report:
- Control board (motherboard) replacement: $250–$400 Source: Fixr - How much does it cost to repair a washing machine?
- Water level / pressure switch replacement: $100–$225 Source: Fixr - How much does it cost to repair a washing machine?
- Drain pump replacement: $300–$400 Source: Fixr - How much does it cost to repair a washing machine?
- Typical washing machine repair: $150–$400 Source: Fixr - How much does it cost to repair a washing machine?
- After-hours / emergency visit surcharge: $100–$200 per visit Source: Fixr - How much does it cost to repair a washing machine?
Replacement tends to make more financial sense once a repair runs past half the cost of buying and installing a new washer. Source: HomeAdvisor - How Much Do Washing Machine Repairs Cost?
Ranges are published estimates, not quotes. See the washing machine repair cost guide and whether to repair or replace a washer.
Getting Ready for the Repair
- Any error code shown on the display
- Where the washer drains (standpipe or laundry sink)
- Whether it is a front loader, a top loader with an agitator, or a top loader with an impeller
Around Sherman
Most washer calls in Sherman come down to the same handful of parts: the drain pump and filter, the lid switch or door lock, the drive belt or coupler, the inlet valve and the suspension.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
In Texas, you can check a license with the Texas plumbing Public License Search or report a problem to the Texas Attorney General, Consumer Protection Division.
How to Choose a Washing Machine Technician Near Sherman
- What is the service call or diagnostic fee, and is it applied to the repair?
- If the problem turns out to be the supply valves or the standpipe, do you handle that or should I call a plumber?
- How often do you repair GE washers, and how quickly can you get parts?
GE Washer Repair FAQs: Sherman, TX
How do I get rid of a washer mildew smell?
Why is my washer leaking?
Should I repair or replace my GE washer?
More Washing Machine Repair in Sherman, TX
More GE Washer Repair Pages Nearby
Check the drain hose, the supply valves and (on a front loader) the drain pump filter, and note the model number before calling. It rules out the simple causes and speeds up a GE repair.