A GE washer shares most of its basic parts with other washers, but its drive design, lid or door lock, controls and error codes are specific to the brand. Below are independent repair companies serving Gilmer, with those that mention GE first, then the nearest appliance repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Washer Repair Near Gilmer
28 repair companies serve Gilmer from within 60 miles. The rest are spread across Tyler (7), Longview (5), and Jacksonville (3). Distances run up to about 57 miles. 1 lists GE specifically. The closest is Ponder Appliance Repair, about 13.2 miles away. Across 25 rated companies, the average public rating is 4.1 stars. Because the nearest shops are farther out, ask each company whether Gilmer is inside its regular service area.
Companies are shown by relevance and distance from Gilmer. A mention does not mean manufacturer certification, so ask each company about its experience with your washer.
| Mention washer work | 7 |
|---|---|
| Mention GE | 1 |
| Distance to the three closest (mi) | 13.2, 17.3, 17.5 |
| With 4.5+ stars and at least 10 reviews | 10 |
| Appliance repair companies in range (60 mi) | 28 |
| Listing Saturday hours | 9 |
Closest matches for Gilmer: Sears Appliance Repair (17.5 miles away, based in Longview, 4.5 stars from 206 reviews, lists Saturday hours); Mr. Appliance of East Texas (37.1 miles away, based in Tyler, 4.7 stars from 1,263 reviews); Raney Appliance Service (38.4 miles away, based in Tyler, 4.5 stars from 57 reviews); 1st Rate Appliance Repair (18.2 miles away, based in Hawkins, 4.9 stars from 409 reviews).
GE Washer Lines and Features
What a GE Washer Technician Deals With
The drain hose should use the included anti-siphon clip and must not be pushed too deep into the standpipe or taped in place, which can siphon water out of the washer. Source: GE Appliances - Front Load Washer - Troubleshooting
Common GE Washer Problems
- Washer not draining. Wait out normal pauses between cycle steps, then look for a kinked or clogged drain hose, a drain set too high, or a clog shown by a Po code or flashing Rinse light. Source: GE Appliances - Top Load Washer - Will Not Drain
- Washer off balance or shaking. Remove some items from an overfilled basket or spread bunched items evenly, then make sure the washer is level. Source: GE Appliances - Frequently Asked Questions About GE Washers
Reading a GE Washer Error Code
| Code | What it means |
|---|---|
| Po (or flashing Rinse light) | The washer is draining slowly, usually from a clog or a pinched drain hose. Source: GE Appliances - Top Load Washer - Will Not Drain |
| dE / E2 | The lid was opened during the cycle; close it and press Start to resume. Source: GE Appliances - Washer - Consumer Help Indicator |
| CAnCELEd | The cycle was paused for more than a day or was stopped by certain errors. Source: GE Appliances - Washer - Consumer Help Indicator |
When to Call for GE Washer Repair
- Musty or mildew smell from the drum or door seal
- Washer will not start or the lid or door stays locked
- Water on the floor under or in front of the washer
What Gets Fixed on a Gilmer Washer Call
Care GE Recommends for Its Washers
- To clean a top load tub, fill it with hot water at the highest level, add a cup of chlorine bleach, and run a regular wash cycle. Source: GE Appliances - Frequently Asked Questions About GE Washers
- On models with UltraFresh Vent, run the vent cycle at the end of each day you do laundry. Source: GE Appliances - Front Load Washer - UltraFresh Vent System with OdorBlock
Brand guides: GE Washer Not Draining or Spinning: What to Check.
GE Washer Repair Cost Ranges
Most GE washer repairs involve common parts and an hour or two of labor. For reference, published cost guides report:
- Control board (motherboard) replacement: $250–$400 Source: Fixr - How much does it cost to repair a washing machine?
- Water level / pressure switch replacement: $100–$225 Source: Fixr - How much does it cost to repair a washing machine?
- Drain pump replacement: $300–$400 Source: Fixr - How much does it cost to repair a washing machine?
- Water inlet valve replacement: $95–$190 Source: Fixr - How much does it cost to repair a washing machine?
- Typical washing machine repair: $150–$400 Source: Fixr - How much does it cost to repair a washing machine?
- Service call / diagnostic fee (often waived if you go ahead with the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
For a drum repair, consider replacing the washer instead if it is more than five years old or has had frequent problems. Source: HomeAdvisor - How Much Do Washing Machine Repairs Cost?
Ranges are published estimates, not quotes. See the washing machine repair cost guide and whether to repair or replace a washer.
What to Have Ready for a GE Washer Call
- Any error code shown on the display
- Whether it is a front loader, a top loader with an agitator, or a top loader with an impeller
- What happens during the cycle (no start, no fill, no drain, no spin, leaks, noise)
Laundry Notes for Gilmer, TX
Most washer calls in Gilmer come down to the same handful of parts: the drain pump and filter, the lid switch or door lock, the drive belt or coupler, the inlet valve and the suspension.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, ยง1301.053 (Texas State Board of Plumbing Examiners)
In Texas, you can check a license with the Texas plumbing Public License Search or report a problem to the Texas Attorney General, Consumer Protection Division.
Questions to Ask a Gilmer Washer Technician
- How often do you repair GE washers, and how quickly can you get parts?
- Do you work on front-load and top-load washers, or only one type?
- If a part has to be ordered, how soon can you come back to finish?
GE Washer Repair FAQs: Gilmer, TX
How do I get rid of a washer mildew smell?
Why does my GE washer show an error code?
Should I repair or replace my GE washer?
Other Washer Repair in Gilmer
GE Washer Repair in Nearby Cities
Check the drain hose, the supply valves and (on a front loader) the drain pump filter, and note the model number before calling. It rules out the simple causes and speeds up a GE repair.